Sigma Envirotech System
Janakpuri, New Delhi, Delhi
GST No. 07ALNPP1668D1ZW
TrustSEAL Verified
Call 0804898785577% Response Rate
SEND EMAIL
De-Mineralization Plants, are available in Two Types, Mainly Two Bed DM Plants and Mixed Bed DM Plants. However, DM Plants are also available with Weak Base & Strong Base Cation & Anion Exchanger. DM Plants are also available with Degasification System to remove alkalinity physically without using chemicals (Saves NaOH).
The Systems have Following Configuration based on the water report or parameters :
Mixed Bed DM Plants (MB) units are offered as a Polisher Unit to get conductivity less than 0.5 micro Siemens/cm or 0.05 micro Siemens/cm conductivity with MB units in Offers Standard DM Plants with FRP / Mild Steel Rubber Lining & SS 316 L (Quartz Lined) construction.
DM Plants (Two Bed & Mixed Bed units) are available in various sizes having cation and anion exchanger unit with 160 mm to 2000 mm diameter with either Valves or Multi Port Valve depending upon the sizes and customer requirement.
In Two Bed DM Plant, Strong Acid Cation Exchanger and Strong Base Anion Exchanger resin are used for reducing Total Dissolved Solids up to 2 - 5 ppm. To check the treated water quality at the outlet, conductivity meter is provided. Degasification unit is also provided to decrease the load on Anion Unit.
Mixed Bed Units are used in series with Two Bed DM Plant as a polisher unit which can produce treated water having conductivity < 1 mS/cm.
Cation Polisher Unit is also available to achieve Acidic Water Quality for Specific applications.
DM Plant produces Treated water having Conductivity less than 10 mS/cm (for Two Bed) and less than 1 mS/cm with pH as desired.
Product Details:
| Minimum Order Quantity | 5 Unit |
| Usage/Application | Battery Water&lab use |
| Purification Capacity | 60lph |
| Water Purification Process | Resin base filtration process |
| Water Source | Borewell Water |
| Brand | Sigma |
Additional Information:
Product Details:
| Minimum Order Quantity | 01 Piece |
| Capacity(LPH) | 100 LPH |
| Inlet Flow Rate (m3/hr) | 100LPH |
| Automation Grade | Semi-Automatic |
| Water Source | Borewell Water |
| Application | Industrial Application, Commercial Application |
| Voltage(V) | 220V |
| Frequency Range | 40-50Hz |
| Installation Service | Yes |
| Max Water Recovery Rate | 80-90% |
| Material of Construction | FRP, SS Powder Coating |
| I Deal In | New Only |
| Country of Origin | Made in India |
We are supplier of Mini DM Water Plant. Demineralized water systems are extensively used in the fields of cooling, power, process, and steam. Two tiny beds filled with polystyrene beads and ion exchange resins are used to pass raw water through. In the first bed, the cations exchange with hydrogen ions, and in the second, the anions exchange with hydroxyl ions. The basic DM plant must have minimum two resin columns, Cation and Anion.
As mentioned above, the salts and minerals present in water carry negatively charged ions called anions and positively charged ions called captions. Both these types get attracted by their counter ions i.e. ions carrying the opposite charge.
These plants feature an IX column containing resins that consist of plastic beads. During the process of demineralization, the ionic functional group gets attached to these beads. These are functional groups that work by holding the ions carrying the opposite charge loosely through a process called mutual electrostatic attraction.
When an ion-exchange cycle is underway, water containing dissolved ions comes in contact with the resin. Ions present in the solution exchange their place with those present on the beads. These ions remain attached to the functional groups of the resins even when the resulting liquid gets drained away. Ion exchange occurs when an ion possesses a greater affinity towards a functional group than the ions the group already carries. The type of ionic contaminants found in the group will decide whether the process would need cationic resins or anionic resins.
In most ion-exchange reactions, the exchange replaces the contaminant ions with less objectionable ions. For instance, the ion exchange sodium softening process is carried out to eliminate hardness ions like Mg2+ or Ca2+ from the solution and replace them with less harmful sodium ions or Na+. Once the process is over, the solution will have little or no hardness but will have a higher concentration of Na+.
The above changes are acceptable for certain applications. However, some procedures require almost 100% removal of the dissolved solids. This makes DM plants such important additions to facilities requiring complete removal of these unwanted solids. A DM plant exchanges cat ions in feed water with hydrogen ions and anions get exchanged with hydroxyl ions. This results in the formation of water. Most plants come with a mixed bed or two-bed configuration. Read on to know about them.
TWO-BED ION EXCHANGE:
A dual bed or two-bed ion exchanger use two (or more) ion-exchange columns or resin beds for treating a stream. Each of these beds contains a different ion exchange resin. During two-bed demineralization, a SAC or strong acid Cation resin is used for treating a stream. This helps in capturing the cat ions dissolved in the water and enables the release of hydrogen ions.
The mineral acid solution you will get as a result will automatically get directed towards the SBA or strong base anion resin bed. When treated in the second resin bed, the DM plant will remove all the anionic contaminants present in the solution and result in the release of hydroxide ions. The combination of these hydroxide ions and the existing hydrogen ions will result in the formation of water.
More and more industries have started to use DM plants to prepare a hefty resource of dematerialized water. However, some industries have been using these units since their discovery. These are industries that need a high level of water purity. Here are some examples:
·Industries that require the use of makeup water or feed for operating high-pressure boilers
·Food & beverage industries (they prepare rinse water using these plants)
·Electronic goods manufacturers
Additional Information:
Product Details:
| Minimum Order Quantity | 1 Unit |
| Capacity(LPH) | 500 LPH |
| Water Source | Borewell Water |
| Capacity Inlet Flow Rate | 500lph |
| OBR | 25m3 |
| Usage/Application | Distilled water /DM Water |
Our organization has renowned in the market for Demineralisation Plant(D.M Plant). These plants are extremely utilized in the market for their reliable performance. Our presented plants are manufactured as per worldwide industry standards utilizing the top component, bought from honest retailers of market. Due to easy to use, this plant is extremely used in the market.
Features :
Flawless finish
Top performance
Low maintenance
Additional Information:
Product Details:
| Minimum Order Quantity | 1 ONE |
| Brand | Sigma |
| Automation Grade | Semi-Automatic, Manual |
| Usage/Application | Distilled water (DM)Plant. |
| Capacity (LPH) | 500 LPH |
| Water Source | River Water |
| Voltage | 0.5hp |
| Application | Industrial Application, Commercial Application |
| Treated Water Quality | Lass tan 20ppm |
| OBR | depend water quality |
| Installation Service | Yes |
| Material of Construction | FRP |
| Capacity Inlet Flow Rate | 65lph |
| Weight | 45klg |
| Operating Pressure | 1.5kg to 2kgcm2 |
| Purification Technology | Cation &Anion based resin use |
| Plant Accessories | online conductivity meter |
Additional Information:
Product Details:
| Voltage | 0.5hp |
| Type | semiautomatic |
| Brand | Sigma |
| Capacity Inlet Flow Rate | 60lph |
| Flow rate | 60lph |
| Water Source | River Water |
| Inlet TDS | 150ppm |
| OBR | 500ltr |
| Phase | single |
| Total Exchange Capacity | As raw water report |
| Maximum Flow Rate | 60lph |
| Automation Grade | Semi-Automatic |
| Maximum Working Pressure | 1.5 to 2 kg |
| Treatment Technique | Resin Base Technology |
| Usage/Application | Distilled water |
Additional Information: